top of page
Cerca

How to Care for Your Epoxy Resin Silicone Molds: How to Clean Resin Silicone Molds


how to clean silicone mold
How to clean resin molds & things to avoid

Introduction

Silicone molds are a critical tool for artisans working with epoxy resin, offering an extensive variety of shapes and exceptional durability when cared for properly. However, without appropriate maintenance, your silicone molds may suffer from reduced effectiveness and lifespan. This blog aims to debunk common misconceptions about silicone mold care, particularly for resin crafts, and provide tips on how to clean resin silicone molds to keep your molds in optimal condition. Misconceptions & Mistakes to Avoid

Common mistakes to avoid when working with resin silicone molds. This reel, brought to you by @handgemachtes_, Visit her Instagram for some resin inspirations


1. Avoid Scrubbing with Soap and Water: Many online resources recommend cleaning molds with soap and water or soft sponges. While this advice is accurate for food-grade silicone molds, it is detrimental for molds intended for epoxy resin. Abrasive cleaning methods can scratch the mold surface, remove the protective oily layer, and potentially cause damage, reducing the shine and lifespan of your molds.

2. No Direct Touching: Avoid touching the mold's inner surface with your fingers or any tools except when pouring the epoxy resin. These can leave marks, diminishing the mold's shine and overall quality, especially for handmade molds.

3. Avoid Unprotected Stacking: Stacking molds directly on top of each other can damage their surfaces. The underside of the upper molds may leave prints or dust on the molds beneath, compromising their clarity and smoothness.


Recommendations for Silicone Mold Care (How to Clean Resin Silicone Molds)

How to Properly Clean and Care for Your Epoxy Resin Molds This reel, brought to you by @handgemachtes_, Visit her Instagram for some resin inspirations

1. Proper Storage: It's crucial to store your molds away from dust and other environmental pollutants that could damage them. An effective practice is to use cardboard layers to separate them when stacking, offering protection against prints and dust.

2. Gentle Cleaning with Scotch Tape: For epoxy resin molds, choose non-abrasive cleaning methods. Utilize a strip of Scotch tape to remove dust, resin leftovers, or lint from the mold's surface. This method is gentle yet effective, ensuring your mold's surface remains intact.

3. Timely Demolding: Don't leave the epoxy resin in the mold longer than necessary. Once fully cured, promptly remove it to prevent potential strain or damage to the mold.

4. Regular Inspection: Inspect your molds regularly for any signs of wear and tear. Small cracks or rough spots can impact the finished look of your resin pieces. It’s better to replace a worn-out mold than to risk the quality of your resin art.

Conclusion


Proper maintenance and how to clean your resin silicone molds can significantly extend their life and maintain the quality of your resin art pieces. By avoiding common misconceptions and adhering to the recommended care practices, you can enhance your resin crafting experience. Remember, each mold is an investment in your craft, and it deserves the utmost care. Happy crafting! We hope this blog has been helpful. For any further questions, don't hesitate to reach us at info@melbmolds.com. We're always here to support your resin art journey!

1 Comment


Some of these are extremely incorrect and in some cases the opposite! As one that uses silicone molds for production purposes i have been though it all for many years. Number one incorrect advice is to clear your mold... NO you should always leave your mold full! Sure you can make your pulls for use but always leave a storage casting. The best way to do it is to keep one casting for storage, usually one of the very first pulls as it is most crisp and accurate. You can clear your mold then ALWAYS clean your mold with mild soap and water, ALWAYS! the residue from your composite or resin is toxic to your silicone and will deterior…

Like
bottom of page